Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterTherma-Tru Impact Garage Doors: The Pembroke Pines Owner’s Guide
We stock and install Therma-Tru-compatible impact garage doors across Pembroke Pines, with most complete door replacements running $2,800 to $6,400 installed depending on size, series, and panel construction. We keep common Therma-Tru hinge assemblies, roller tracks, bottom seals, and weatherstripping on our service trucks, so a failed component can often be handled in one visit. Most Pembroke Pines homeowners discover a problem the morning after a storm: the door binds halfway up, one panel sits proud of the track, or the bottom seal has torn loose and daylight is showing under the door.
Therma-Tru builds doors rated for windborne debris, but South Florida humidity and salt air punish the hardware long before the panels give out. We’ve replaced more corroded roller brackets and seized hinges in Pembroke Falls, SilverLakes, and Grand Palms than we have storm-damaged panels. The door is only as sound as its weakest hinge, and on an impact-rated door, that hinge is doing structural work, not just keeping panels connected.
Which Therma-Tru Models This Applies To
Therma-Tru’s impact garage door line crosses several series, and the part you need depends on which one you have. The Pulse and Classic-Craft garage door lines share similar hardware, but the reinforcement plates and hinge offsets differ between single-car and double-car configurations. What fits a 16-foot door will not necessarily fit a 9-foot door, even in the same series.
Before you order anything, look at the inside face of the bottom panel. Therma-Tru stamps a data plate near the hinge line with the series name, panel thickness, and wind-load rating. If that sticker has faded or peeled, measure the panel height from the top edge of one panel to the bottom edge. Therma-Tru residential panels run 21, 24, and 28 inches, and that measurement alone rules out a lot of wrong guesses. The wind-load rating matters more than the series name: Pembroke Pines sits in a high-velocity hurricane zone, and a door rated for 130 mph wall pressure is not interchangeable with one rated at 170 mph, even if both are Therma-Tru.
We recommend OEM Therma-Tru parts for anything load-bearing: hinges, struts, reinforcement stiles, and the bottom panel itself. For rollers, seals, and hardware that wears predictably, quality aftermarket equivalents from National Hardware or Action Industries work well and often outlast the original. We’ll show you the difference on paper before we install either one.
Signs Your Therma-Tru Impact Garage Door Is Failing
- Door binds or jerks when opening. A panel has slipped on its hinge, or a roller has flattened and is dragging in the track. On an impact door, that bind is putting torque on the hinge plates they were never designed to absorb. Left alone, it bends the stile.
- Visible rust streaking from hinge points. Pembroke Pines humidity causes galvanic corrosion where the steel hinge meets the aluminum panel frame. Once rust streaks appear, the hinge has lost its protective coating and the bearing surface is failing.
- Bottom seal torn or curled back. The rubber T-seal that runs under the bottom panel keeps wind-driven rain and debris from blasting under the door. A torn seal lets water in during every summer storm, which is how you discover it: wet spots along the garage floor.
- Door sags several inches on one side when disconnected from the opener. This usually means a broken torsion spring on one side, or a failed corner bracket. On an impact door, the panels are heavier than standard, so the spring failure shows up as a pronounced sag, not a gradual droop.
- Loud pop followed by the door slamming down if released. That pop is a torsion spring letting go. Do not operate the door. Disconnect the opener and call us. High-tension springs store enough energy to cause serious injury if they release while someone is underneath.
Replacement Cost & What’s Included
In Pembroke Pines, replacing a failed Therma-Tru impact garage door panel runs $380 to $850 installed, depending on panel width and wind rating. Full door replacement with impact-rated Therma-Tru panels runs $2,800 to $6,400. Hardware repairs, like hinge and roller replacement, run $180 to $420 including parts and labor.
What drives the range is panel size, wind rating, and whether the existing track and spring assembly can be reused. A 170-mph rated 16-foot door costs more than a 130-mph 9-foot door because the reinforcement stiles and hinge hardware are heavier gauge. Every quote we write is a written line-item price, no change orders, no surprises on the bill. The Done Right Promise covers the labor and the fit, and we register both manufacturer warranty layers in writing before the truck leaves your driveway. That is The Keystone Standard, and it applies to every part we touch, from a single hinge to a full door.
Parts pricing for common Therma-Tru items:
- Hinge assembly, steel reinforced: $28 to $64 per hinge, installed
- Nylon roller with sealed bearing, set of 10: $90 to $140 installed
- Bottom T-seal, 16-foot door: $70 to $110 installed
- Single impact-rated panel, standard 24-inch: $380 to $850 installed
- Complete impact door, 9-foot: $2,800 to $3,900 installed
- Complete impact door, 16-foot: $4,200 to $6,400 installed
DIY or Call Us?
A homeowner can safely do two things: inspect the bottom seal for tears and check the rollers for visible flat spots with the door closed. After that, I encourage you to stop. Any repair that requires loosening hinge bolts, winding or unwinding torsion springs, or removing a bracket from the track is work to leave to someone who does it every week.
Torsion springs on an impact-rated Therma-Tru door are under enough tension to break a bone or worse if the winding bar slips. Even a hinge replacement on these doors is different from a standard door because the hinge plate doubles as a reinforcement point for wind load. If it is set even slightly out of plane, the next storm will find it. That is not a guess, it is physics.
If you’re in Pembroke Pines and your Therma-Tru door is binding, rusted, or sagging, call (863) 208-6105. We will tell you over the phone whether it sounds like a simple roller job or a panel replacement, and we’ll quote you a written price before we schedule. If the pane is not true, the job is not done, and that goes for door panels too.
FAQs
Expect 12 to 18 years from the panels on a Therma-Tru impact door in Pembroke Pines, with the bottom panel and bottom seal failing first because of storm-driven water and salt air. Hardware like hinges and rollers typically needs replacement at the 8 to 10 year mark, sometimes sooner in neighborhoods east of University Drive where salt exposure is higher. Call (863) 208-6105 if your door is in that age range and starting to bind.
Small dents and surface scratches can sometimes be patched and re-painted, but structural damage to a wind-rated panel means replacement, not repair, because the panel’s reinforcement stile has been compromised. On a Therma-Tru impact door, a panel that has taken a hit is no longer doing its wind-load job even if it looks okay from the outside. We’ll inspect it and show you what we’re seeing before we recommend either path.
A hinge and roller replacement on a Therma-Tru impact garage door takes 90 minutes to two hours on site, and we carry common Therma-Tru hinge sizes and roller sets on the truck so there is no second appointment. Full panel replacement is usually a half-day job. Call (863) 208-6105 for an exact time frame on your specific door.
We stock Therma-Tru-compatible hinges, rollers, seals, and weatherstripping on our service trucks, along with parts for PGT, CGI, and CWS impact doors. Odd-size panels and full door systems are ordered direct from the manufacturer and typically arrive in 5 to 10 business days. We’ll tell you up front what is on the truck and what has to be ordered before we take the job.
Contact TruePane Windows & Doors
If your Therma-Tru impact garage door is failing, call (863) 208-6105 and talk to a person. We’ll ask a few questions, give you an honest read over the phone, and schedule a free estimate at your Pembroke Pines home. Dale Kessler grew up in Pembroke Falls and has spent the better part of three decades measuring, fitting, and setting glass and doors across South Florida. If it is not in writing, it is not a guarantee, it is a guess. We put everything in writing, including the Done Right Promise and both manufacturer warranty layers, before the truck leaves your driveway.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Pembroke Pines and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.