Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCWS Door Installation: The Pembroke Pines Owner’s Guide
CWS door installation in Pembroke Pines typically runs $220-$480 for a complete replacement, depending on the door model and whether the frame needs re-shimming or sealing. We stock most common CWS door hardware and panels on our trucks, so a service call usually ends with the door set and closing true the same day. Most owners discover a problem the way you probably did: the door starts binding at the top corner in July, or the sweep lets afternoon rain run onto the tile, or the panel simply stops locking flush against the jamb.
We’re an independent installer, not affiliated with CWS, but we work on their doors every week across Pembroke Pines and western Broward County. Dale Kessler grew up in the Pembroke Falls neighborhood and has been setting doors in these houses for the better part of three decades, so he knows which CWS models hold up in Florida humidity and which ones need attention by year eight.
Which CWS Models This Applies To
CWS manufactured several door lines over the years, and the compatibility details matter more than most homeowners expect. The two series we see most often in Pembroke Pines are the CWS aluminum outswing doors common on 1990s-era patio entrances and the later swing-clean or hinged French door units that replaced them. If you can find the sticker on the hinge edge of the door slab, the model number usually starts with a CWS prefix followed by a four-digit series code. No sticker? Measure the door slab thickness and the hinge spacing before you call. Older CWS units used a 1-3/8 inch slab with non-standard hinge mortises, and a generic replacement door will not sit right in that opening no matter how carefully it is hung.
On the OEM-versus-aftermarket question, we’re straightforward about it. For CWS lock sets, rollers, and hinges, a quality aftermarket part from a Florida-rated supplier typically performs as well as the original and costs 30-40% less. For the door panel itself, especially on impact-rated units, we recommend staying with a CWS-spec panel or a documented equivalent. We can quote both on paper side by side so you see exactly what you’re paying for, and we register the manufacturer warranty on either path before the truck leaves your driveway.
Signs Your CWS Door Installation Is Failing
- Door binds or scrapes at the top corner in summer. Aluminum frames expand in South Florida heat, and a CWS door that was set slightly out of true will show it first at the header. The fix is a re-shim and hinge adjustment, not a new slab, unless the frame has twisted beyond correction.
- Water on the floor after a heavy Pembroke Pines downpour. The sweep or threshold gasket on CWS doors tends to flatten and crack after seven or eight years, especially on west-facing exposures that catch the afternoon sun. The channel is CWS-specific in width, so a universal sweep leaves gaps at the corners.
- Door fails the dollar-bill test. Close the door on a dollar bill. If it slides out with no resistance anywhere along the jamb, the weatherstripping or the alignment is gone. Resistance should be consistent all the way around.
- Lock set turns but the latch won’t throw. This is usually a misaligned strike plate from a settling slab, but it can also mean the internal CWS lock cassette has stripped. We carry replacements for both the older mortise-style CWS locks and the newer bored units.
- Visible corrosion at the bottom rail or hinge screws. Salt air and pool chemicals accelerate this in Pembroke Pines more than people expect. Once the hinge screws start pulling out of corroded aluminum, the door is hanging by fresh air and needs immediate attention.
Replacement Cost & What’s Included
A complete CWS door installation in Pembroke Pines, including the new door slab or panel, hinges, weatherstripping, and labor, typically lands between $220 and $480. The range depends on three things: whether we’re replacing a component or the full slab, whether the existing frame is still square and reusable, and whether the door is a standard or impact-rated CWS unit. Impact-rated panels run higher, and a frame replacement adds another $130-$190 to the total.
Every quote we write is a fixed price with no change orders and no surprise line items on the bill. The Keystone Standard means both manufacturer warranty layers are registered in writing and their durations stated before we leave. The workmanship on the installation is covered by our Done Right Promise. If it is not done right, we make it right. No paperwork, no arguing.
DIY or Call Us?
You can safely check a few things yourself. Look for the CWS model sticker, note whether the door binds at the top or drags at the bottom, and check if water is coming under the panel or around the frame. That information helps us come prepared.
What we’d ask you not to do is pull the door slab off its hinges to “adjust” it, especially on a CWS aluminum outswing unit. These doors are heavier than they look, and a dropped slab takes out tile, toes, or both. The hinge adjustments and frame re-shimming on CWS doors are best left to someone who has done it a few hundred times. Call (863) 208-6105 and we’ll send a background-checked, uniformed tech who will measure twice and quote before any work starts.
FAQs
Expect 10 to 15 years from the door slab and hardware, though weatherstripping and sweeps typically need replacement every 5 to 7 years in Florida’s heat and humidity. You can stretch the lifespan with a maintenance check that checks alignment, seals, and hinge wear before they become failures. Call (863) 208-6105 to schedule one.
Yes, in about 60% of the jobs we see, the fix is a new sweep, re-shimmed hinges, or a replacement lock cassette, not a full slab replacement. We’ll always tell you the repair option first if it is honest. Call (863) 208-6105 for an assessment, and we’ll quote both paths if it makes sense.
Most standard CWS door replacements are completed in a single visit, usually two to four hours. Frame replacements or impact-rated panels can run longer, and we’ll tell you the timeline before we schedule.
We keep the most common CWS sweeps, thresholds, hinges, and lock cassettes on our service trucks, plus a rotating inventory of door panels at our shop. We also stock parts for Andersen, and Pella doors. If we don’t have your spec on hand, we’ll have it in hand within a few business days and tell you that before you commit.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Pembroke Pines and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.